Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a substantial resurgence throughout the nation, Gentle Giant wants to make certain that these classic, gorgeous makers stay damage-free while being transported. Oh, and we desire the individuals moving them to be safe, too.

At first glimpse, pinball makers can appear intimidating to move since of their fragility, size, and weight. Thankfully, our competent Giants have a couple of techniques up their sleeves to ensure your pinball is moved with ease.
Folding Down the Headbox

Most of modern-day pinballs (made in the last Twenty Years or so) have a hinge system which enables the headbox to be folded down. Early pinball makers had their headboxes bolted on, utilizing either two or four bolts. All Electro-Mechanical pinballs utilize this system, in addition to the early Solid State devices.

Later on makers have hinges and use a latching system to keep the headbox upright. There might likewise be 2 bolts inside as added safety, in case the lock is broken or mistakenly un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball machines, you have to eliminate the headbox rear gain access to panel to access to the bolts and plugs inside. Typically this panel has a lock on it to keep it in location, however over time the key may have been lost. Frequently, there is a screw keeping this panel in place.

Once inside, eliminate the bolts and disconnect the big connectors that have electrical wiring decreasing into the maker. You might want to label these ports to put them back in the best area, however they should be different sizes, making it tough to plug back improperly.

You can now get rid of the headbox completely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in location.
Early Solid State Pinballs

For early Solid State Pinballs, you will need to eliminate the back glass. There is a lock located on the headbox in one of 3 areas: the left-hand side at the top, right-hand side at the leading or on top of the headbox in the.

Once unlocked, remove the back glass by lifting it up utilizing the lift channel (at the bottom of the glass), then pull it out from the bottom.

Open up the back box lamp panel by raising the lock situated on either the left-hand side or right-hand side. The panel can now swing out to you, and offer you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to raise the lamp panel in order to swing it open.

Now that you are inside, you can eliminate the bolts, and any plugs that have wires decreasing into the maker. You might wish to label these plugs to put them back in the right spot. You may not require to eliminate the plugs, as the circuitry needs to be long enough to permit the headbox to be folded down.

At this point, you can lock up the lamp panel and replace the back glass.
Modern Solid State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system situated at the back of the click site headbox. Utilizing the provided secret, turn the lock 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the machine. This is a simple setup and requires no tools.

If you can now fold down the head box onto the cabinet, you're done. Ensure you utilize some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.

You need to get inside if you can not fold the head box down. There is a lock located at the top of the back glass in the. Use the supplied key to unlock, and eliminate the back glass by lifting it up from the bottom, and after that pulling it out see here from the bottom.

Next, you will need to remove the display panel. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

Eliminate the two bolts, put the back box back together, and fold down the head box onto the cabinet. Ensure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.
Eliminating the Legs.

Pinball Device legs are held in place by eight bolts. They will be either 5/8 inch or 9/16 inch heads. The contemporary pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be eliminated, and the legs will come off.

These captive nuts and threaded plates can be damaged, and the use of extra nuts may have been required. If this holds true, you will have to open the front door of the pinball, slide out the playfield glass, and raise the playfield.

With the front door (coin door) open, move the lock down bar lock throughout and get rid of the lock down bar. Then move out the playfield glass, and put in a safe location. Next, lift up the playfield by putting your hand where the ball drains, and lift the playfield up.

You ought to now have access to any nuts that may have been used. Once any nuts have been removed, change the playfield glass and lock down bar, and lock the front door.

Make certain to mark or keep in mind which legs are for the front and back, as they will be changed in a different way to fit.
Packing the Pinball.

You are now prepared to transfer your pinball device. Before you load it, make sure you remove the pinballs so they don't bounce around throughout transportation.

It may be easier to remove the legs simply prior to filling the maker if you are moving the pinball utilizing a van or SUV. Get a buddy to have and help one of you supporting the pinball, while the other removes the front legs. Move the maker in, then eliminate the back legs. It is much easier to fill the maker front.

Make sure you strap the pinball in, as you do not want it moving if you need to stop unexpectedly!

For Electro-Mechanical pinball devices, you need to remove the headbox rear access panel to get access to the bolts and plugs within. (Some more recent Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

If you are moving the pinball using a van or SUV, it might be much easier to eliminate the legs just prior to loading the machine. Get a pal to have and help one of you supporting the pinball, while the other removes the front legs.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Tips From the Moving Company Pros: Ways To Move a Pinball Maker”

Leave a Reply

Gravatar